(13) Standard Port Contour Cutter, Short Series - Carbide Tipped, PS10035 (AS1300) Port
APPLICATION:
This tool counterbores, countersinks, provides a radius and produces a tap drill diameter in one
pass. Countours are ground to insure concentricity. Cutter geometry permits the use of these
tools with most common materials
(13) Broach Tool - Hand Held, PS10035 Port Serrations
NOTES: Unless Otherwise Specified
Replacement cutters may be purchased individually
Inspection of noted runout and use of controlled minor diameter per Rosan PS10035 port spicspecification will provide an allowable maximum runout of .009 between serration major diameter and controlled minor diameter after broaching.
APPLICATION: This broach tool, when used in arbor, hydraulic presses or manually, is designed to produce serrations in the counterbore wall of ports prepared per PS10035. The tool will broach aluminum, magnesium, and many steels with hardness of 32 HRC or less. Successful broaching of harder or tougher material may be ...
(13) Broach Tool - Non-Impact, PS10035 Port Serrations, for Material up to 40 HRC
NOTES: Unless Otherwise Specified
Usage of tool is described in TSB52273. This tool will broach serrations into most materials with hardness up to 40 HRC.
Two extra cutters are provided with each tool.
Replacement cutters may be purchased individually
Replacement studs may be purchased individually
Use of this tool will provide an allowable maximum runout of .009 between serration major diameter and controlled minor diameter (REF: PS10035) after broaching.
(13) Broach Tool - Poco Graphite Electrical Discharge Machining, PS10035 Port Serrations
NOTES: Unless Otherwise Specified
MATERIAL: UNION POCO GRADE EDM-3 GRAPHITE, with option of alloy steel shank.
This tool is designed to provide approximately 10 times the life of tools made from brass (RFOPB5000ED Series).
When using this tool, the machine should be set to produce a burn which is .009 to .011 larger on the diameter than “A”. This will allow the lockring to fit into the serration produced with about .004 to .005 clearance. The applicable lockring may be used to gage the port serration
CAUTION: Care must be taken when machining to provide the following ...
MATERIAL: COPPER TUNGSTEN, with option of alloy steel shank.
When using this tool, the machine should be set to produce a burn which is .002 to .003 larger on the diameter than “A” Dia. This will allow the lockring to fit into the serration produced with about .004 to .005 clearance. The applicable lockring may be used to gage the port serration.
CAUTION: Care must be taken when machining to provide the following requirements: A maximum runout of .009 must be maintained between serration major dia and controlled minor dia (specified in Rosan PS10035 ...
(13) Broach Tool Wobble Broach Machining, PS10035 Port Serrations
NOTES: Unless Otherwise Specified
Wobbling Drift Hold is ordered separately using part number W37601.00
Cutter and Screw combination can be ordered separately for spares or replacement
USAGE: These tools are designed to broach serrations into counterbore of ports PS10035 (AS1300) and PS10048 with parent material hardness up to 40HRC. For harder materials, electrical discharge broach tools are available.
(11) Broach Tool Wobble Broach Machining, PS10035 Port Serrations
NOTES: Unless Otherwise Specified
Wobbling Drift Hold is ordered separately using part number W37601.00
CAUTION: Care must be taken when machining to provide the following requirements: A maximum runout of .009 must be maintained between serration major dia and controlled minor dia (specified in Rosan PS10035 port specification) after broaching.
Cutter is replaceable and can be ordered separately for spares. One spare cutter is supplied with each tool assembly.
The RF( )CRA (sizes 04, 06 and 08) or RF( )CR (sizes 02 thru 32) may also be used to clear chips from PS10035 Port. For further information refer to bulletins TSB89-0606 (CRA Series) or TSB85-0228 (CR Series)
Part number RF5332W will also be marked on RF6932W wrench; part number RF6915W will also be marked on RF6916W wrench.
These wrenches may be used to wrench in RF5000, RFH5000, RF75000, RFH7500, RF7700, RF9800, RFK9800, RF9900, RFH9900, RFK9900 series, as well as other adapters and check valves.
(10) Standard Port Contour Cutter, Short Series - Carbide Tipped, PS10040 (AS1300) Port
APPLICATION:
This tool counterbores, countersinks, provides a radius and produces a tap drill diameter in one
pass. Countours are ground to insure concentricity. Cutter geometry permits the use of these
tools with most common materials
(10) Broach Tool - Hand Held, PS10040 Port Serrations
NOTES: Unless Otherwise Specified
Replacement cutters may be purchased individually
Inspection of noted runout and use of controlled minor diameter per Rosan PS10035 port spicspecification will provide an allowable maximum runout of .009 between serration major diameter and controlled minor diameter after broaching.
APPLICATION: This broach tool, when used in arbor, hydraulic presses or manually, is designed to produce serrations in the counterbore wall of ports prepared per PS10035. The tool will broach aluminum, magnesium, and many steels with hardness of 32 HRC or less. Successful broaching of harder or tougher material may be ...
(10) Broach Tool - Non-Impact, PS10040 Port Serrations, for Material up to 40 HRC
NOTES: Unless Otherwise Specified
This tool will broach serrations into most materials with hardness up to 40 HRC.
Two extra cutters are provided with each tool.
Replacement studs may be purchased individually
Replacement cutters may be purchased individually
Use of this tool will provide an allowable maximum runout of .009 between serration major diameter and controlled minor diameter (REF: PS10040) after broaching.
(16) Porting Tool - Carbide Tipped, PS10047 (MA2110-EN2602) Port
APPLICATION:
This tool counterbores, countersinks, provides a radius and produces a tap drill diameter in one
pass. Countours are ground to insure concentricity. Cutter geometry and material permit the use of this tool with most common materials.
(13) Broach Tool - Impact Type, PS10047 (MA2110-EN2602) Port Serrations
NOTES: Unless Otherwise Specified
Replacement or spare cutters may be purchased individually.
Noted runout and the controlled minor diameter of the PS10047 port will result in a permissible maximum runout of 0.23 between the serration major diameter and the controlled thread minor diameter after broaching.
APPLICATION: This broach tool is designed to produce serrations in the counterbore of PS10047 ports. The tool will broach into aluminum,magnesium and materials with a maximum hardness of 32 HRC.
METHOD:Insert the pilot into the tap drill hole of the port and apply sufficient force to the top of ...
(13) Broach Tool - Non-Impact, PS10047 (MA2110-EN2602) Port Serrations, for Material up to 40 HRC
NOTES: Unless Otherwise Specified
Two extra cutters are provided with each tool. Replacement or spare cutters may be purchased individually.
Noted runout and the controlled minor diameter of the port will result in a permissible maximum runout of 0.23 between the serration major diameter and the controlled thread minor diameter after broaching.
Bearings manufactured by The Torrington Company, CT, USA.
APPLICATION: This broach tool is designed to produce serrations in the counterbore of PS10047 ports. The tool will broach into aluminum,
magnesium and other materials with a ...
(13) Broach Tool Wobble Type, PS10047 (MA2110-EN2602) Port Serrations
NOTES: Unless Otherwise Specified
Replacement or spare Cutter and Screw Combinations may be purchased individually.
After broaching, a maximum runout of 0.23 is permissible between the serration major diameter and the controlled minor diameter of the port thread.
APPLICATION: This broach tool is designed to produce serrations in the counterbore of PS10047 ports. The tool will broach into aluminum,
magnesium and materials with a maximum hardness of 40 HRC.
METHOD: THis tool is used in conjunction with a Wobbling Drift Holder, a product of The Wickrman Corp., 10325 Capital Ave., Oa k Park, ...
